# changelog

author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 6.30
changelog:
  -     Fixes the following issues:
      
        * DDR cache could be randomly disabled after several boots
        * The controller could become unresponsive while in HBA mode during the creation of a partition/file system
      
      .


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 6.60
changelog:
  -      Issue where the QueryAsynchronousEvent could potentially provide incorrect response data
        * Issue where the Cache could potentially get disable after several reboots


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 6.88
changelog:
  -     Fixes the following Issues
      
        * SATA drive could stop responding  while on HBA mode when non-NCQ commands are executed
        * Controller could stop responding when upgrading due to the DDR Cache Module exceeding its limitations
        * SSD Cache module could become disable while upgrading FW
        * Data from the HPE Smart Drive Backplane could potentially become corrupted if a non-HPE carrier is present


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 7.00
changelog:
  -      Occasionally  the drive will not accept any IO's after running Sanitize command for a period of time due to the FW being out of sync with the drive during that time
        * Non-HPE drives could report "Task Set Full" due to the drives reaching the qdepth limit during heavy workload
        * Raid volume is not discovered due to a bad drive consuming two slots during hotplug
        * Data could become inaccessible when upgrading from firmware versions prior to 4.5x
        * The controller could stop responding when executing a SCSI verify command due to a CPU exception
        * The system could stop communicating due to an I/O command timeout
        * While on HBA mode, a drive could stop responding due to an early allocated buffer release
        * A SAS drive WWN is reported inaccuratelyy due to an incorrect report causing the driver to be out of sync with the device
        * If using a 4G module, the controller could stop responding due to the SSD Cache metadata exceeding its limits during a Backup
        * SSD Smart Cache module become disabled due to a reduction in usable cache space


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.0.8.0
changelog:
  -     Customers who wish to support the HP Smart Array P721m or the HP D6000 Disk
      Enclosure with the HP 6Gb SAS BL Switch must ensure that the HP 6Gb SAS BL
      Switch Firmware is at 3.0.8.0 or greater.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.0.8.0
changelog:
  -     ***Enhancements/New Features:****
      
        * Added context sensitive help in GUI to better describe High Performance Connection.
        * Added support for: 
          * HP Smart Array P721m.
          * HP D6000 Disk Enclosures.
        * HP Serial Attached SCSI (SAS): 
          * Added support to detect signal integrity issues between SAS switch and Disk Enclosures.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.0.8.0
changelog:
  -     *Firmware Dependency:**  
      The devices listed below require minimum FW deliverables with HP Storage
      Manager version 3.0.8.0
      
      Device Minimum Version
      
        * HP D2600\D2700 Disk Enclosure 0134
        * HP 600 Modular Disk System 3.44
        * HP P2000 Modular Smart Array TS230P06
        * HP Smart Array P711m\P712m 5.32
      
      **Problems Fixed**:****
      
        * Clock in SAS switch now reports local time, determined by Time Zone setting in Blade Enclosure.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.1.3.0
changelog:
  -     *Firmware Dependency:**  
           The devices listed below require minimum FW deliverables with HP Storage Manager version 3.1.3.0
      
           Device Minimum Version
      
        * HP D2600\D2700 Disk Enclosure 0147
        * HP 600 Modular Disk System 3.60
        * HP P2000 Modular Smart Array TS230P06
        * HP Smart Array P711m\P712m 5.70
      **Problems Fixed:**  
           Firmware 3.1.3.0 resolved the following issues:   
      
        * After flashing and resetting a D6000 enclosure, servers might not discover the enclosure for an extended period of time.
        * Upon replacement, a new switch might not be able to zone some of the devices.
        * Customer might not be able to download diagnostic logs.
        * Onboard Administrator (OA) sometimes alternated the status of the switch between Ok and Degraded.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.5.5.0
changelog:
  -     ***Firmware Dependency:****  
           The devices listed below require minimum FW deliverables with HP Storage Manager version 3.5.5.0:
      
        * **Device, Minimum Recommended Version**
        * HP D2600/D2700 Disk Enclosure, 0147
        * HP 600 Modular Disk System, 3.60
        * HP D6000 Disk Enclosure, 2.38
        * HP P2000 MSA Array System, TS230P06
        * HP Smart Array P711m/P712m Controller, 5.70
        * HP Smart Array P721m Controller, 3.54
      **Problems Fixed:**  
           Firmware 3.5.5.0 resolved the following issues: 
      
        * The folder "/var/log/messages" was not cleaned up correctly.
        * A newly hot-plugged blade server might not have displayed in Virtual SAS Manager (VSM) GUI and CLI.
        * Under rare circumstances, rebooting servers might have caused loss of paths to the drives.
        * Under rare circumstances, VSM GUI and CLI might become unresponsive after flashing and resetting the switch.
        * iLO might not have been accessible for long time on servers if multiple switches were booted up at the same time.
        * If a storage enclosure failed or was removed, or drives were lost, VSM might not have reported a hot removal.
        * When a SAS cable was connected or disconnected on a port, false DWORD errors might have been reported.
        * Some errors might not have been indicated by the LEDs on the switch ports.
        * A newly added server configured with an HP 1210m controller could not detect MDS600 storage enclosure.
        * After updating a storage enclosure firmware, the success message was not aligned properly in VSM.
        * While creating a new zonegroup, a message displayed that indicated the existence of a duplicate zonegroup.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.0.1.0
changelog:
  -     *Enhancements/New Features:**  
      
        * Added support for the HP MSA 2040 Storage System.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.0.1.0
changelog:
  -     ***Firmware Dependency:** **
      
           The devices listed below require minimum FW deliverables with HP Storage Manager version 4.0.1.0:
      
      **Device, Minimum Recommended Version**
      
        * HP D2600/D2700 Disk Enclosure, 0147
        * HP 600 Modular Disk System, 3.60
        * HP D6000 Disk Enclosure, 2.38
        * HP P2000 MSA Array System, TS230P06
        * HP Smart Array P711m/P712m Controller, 5.70
        * HP Smart Array P721m Controller, 3.54
      **Problems Fixed:**  
      
        * Fixed issue in which the "Create and Assign Zone Group" operation did not display an error message if the required zone group name was blank.
        * Fixed a rare issue where repeatedly rebooting the switch may cause some drives in the storage enclosure to not be detected.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.1.1.0
changelog:
  -     *Problems Fixed:**  
      The following issues are now resolved:
      
        * If the switch was assigned a static IP address using the Onboard Administrator EBIPA feature, then the switch might generate continuous Cold Start SNMP traps and overfill logs.
        * A storage enclosure flash operation might fail when run from Virtual Storage Manager (VSM) CLI while the GUI was open.
        * Link rate of a disk was incorrectly displayed in VSM GUI and CLI.
        * In rare cases, multiple resets of a switch would cause the Smart Array to lockup 0xAB.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.1.1.0-2.1
changelog:
  -      **Customers who already installed firmware version 4.1.1.0 do not need to update to 4.1.1.0(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.1.1.0-2.1
changelog:
  -     *Enhancements/New Features for FW version 4.1.1.0(B):**
      
        * Added component support for x64 operating systems.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.2.1.0
changelog:
  -      When a HP 6Gb SAS BL Switch  is configured with a very large number of physical drive bays (such as, 400 or more) and/or a large number of zone groups (such as, 16 or more), the switch manager GUI may not be able to load the configuration and show enclosure information.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.2.2.0
changelog:
  -      Firmware was changed to make it more robust and resilient to handle possible unresponsiveness due to a potential deadlock between multiple processes. If deadlock was to occur, it might cause an inability to establish an SSH session with the switch.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.10
changelog:
  -     *Enhancements/New Features:  
      **     Support for HP ProLiant BL 460c G7 server.   
           Support for HP NC522m Dual Port Flex-10 10GbE Multifunction BL-c Adapter.   
           Removed VCM requirement for Primary/Secondary VC Interconnect modules to be placed in I/O bays 1 and 2.   
           Support for Brocade 804 8Gb FC hBA for HP BladeSystem c-Class.   
           Provides the ability to display Fibre Channel and Ethernet port statistics via the VCM CLI.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.10
changelog:
  -     *Important Notes:  
      **     Read the latest version of HP Virtual Connect Release Notes. It can be found in the "User Guide" section, under the URL: [http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentType=SupportManual&amp;lang=en&amp;cc=us&amp;docIndexId=64180&amp;taskId=101&amp;prodTypeId=3709945&amp;prodSeriesId=3552695](http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentType=SupportManual&amp;lang=en&amp;cc=us&amp;docIndexId=64180&amp;taskId=101&amp;prodTypeId=3709945&amp;prodSeriesId=3552695)  
        
        
      **Problems Fixed:**  
           Dot1dBasePortMTUExceededDiscards incrementing even with jumbo frames enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.15
changelog:
  -     *Enhancements/New Features:  
      **      Added support for the HP VC FlexFabric 10Gb/24-port Module   
            Added support for the HP NC551m Dual Port FlexFabric 10Gb Converged Network Adapter.   
            Added support for the HP ProLiant BL2x220c G7 Server Blades.   
            Added support for the HP NC552m 10Gb 2-port Flex-10 Ethernet Adapter.   
            Added support for the HP NC542m Dual Port Flex-10 10GbE BL-c Adapter.   
            Added support for the HP NC551m Dual Port FlexFabric Adapter protocol personality change between FCoE and iSCSI.   
            Added support for full iSCSI and TCP offload with NC551m FlexFabric adapters and FlexFabric/Flex-10 modules.   
            Added support for iSCSI boot with NC551m FlexFabric adapters and FlexFabric/Flex-10 modules.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.15
changelog:
  -     *Important Notes:  
      **     Read the latest version of HP Virtual Connect Release Notes. It can be found in the User Guide section, under the URL:   
              
        [http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentT
      ype=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=101&prodTypeId=3709945
      &prodSeriesId=3552695](http://h20000.www2.hp.com/bizsupport/TechSupport/Docume
      ntIndex.jsp?contentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=10
      1&prodTypeId=3709945&prodSeriesId=3552695)  
             
        
        
      **Problems Fixed:**  
            Resolved an issue, that can result in a network outage, when a profile is created with duplicate multiple networks.   
            Resolved an issue were Virtual Connect Manager (VCM) will reset modules that have port mirroring enabled when VCM restarts, and will casue a network outage.   
            Resolved an issue were VC modules do not provide information about CPU, part number, etc. via Command Line Interface (CLI).   
            Resolved an issue when using VC CLI, were a user is unable to add LDAP groups with names containing spaces.   
            Resolved an issue when a profile is created with multiple networks that use a Shared Uplink Set (SUS) without selecting any networks, and if this profile is applied to a server with Flex NICs, this will result in a segmentation fault, VCM SEGV.   
            Resolved an issue were 'About' HP VCM pop-up window was causing IE8 to crash, which results, in the About table not being displayed.  
            Resolved an issue with VCM SEGV when the user has a profile (with multiple networks defined in a connection without a network being configured), then edits the profile without making any changes, and then applies the profile to a server with Flex-10 LOM.
      
      **Known Issues:  
      **In a double-dense domain configuration, interconnect bays 7 and 8 should not be used to create a FC Fabric. The fabric should instead be created on bays 5 and 6. If a fabric is created on bays 7 or 8 using VCMCLI, an incorrect error message may be displayed 'ERROR: Module not found' instead of 'ERROR: A fabric is not allowed to be created with the specified bay for a double-sense configuration'   
            When a Blade server port has multiple FlexNICs defined (one of them is defined as FCoE) and the FCoE FlexNIC is deleted, the band width does not redistribute to other active FlexNICs even through the GUI will show it has.   
            If the Primary VC modules loses power or is removed, a Profile Status change trap is not sent as it should be. Work-around: When the Primary VC module loses power or is removed, the cpqHoSWRunninagStatusChangeTrap trap (defined in the cpqhost.mib MIB) will be sent by the backup VC module when it becomes Primary. A sample trap is shown below:   
                 
               Enterprise Specific Trap (.11017) Uptime: 20 days, 2:54:46.44,   
               SNMPv2-MIB::sysName.0 = STRING: bay2TC,   
               SNMPv2-SMI::enterprises.232.11.2.11.1.0 = INTEGER: 10,   
               SNMPv2-SMI::enterprises.232.11.2.6.1.1.2.1 = STRING: "aus-c7000-13_vc_domain",   
               SNMPv2-SMI::enterprises.232.11.2.6.1.1.3.1 = STRING: "HP Virtual Connect Domain Manager",   
               SNMPv2-SMI::enterprises.232.11.2.6.2.0 = STRING: "VCM Domain status trap",   
               SNMPv2-SMI::enterprises.232.11.2.6.1.1.4.1 = STRING: "3.15",   
               SNMPv2-SMI::enterprises.232.11.2.6.1.1.12.1 = INTEGER: 4,   
               SNMPv2-SMI::enterprises.232.11.2.6.1.1.13.1 = INTEGER: 5,   
               SNMPv2-SMI::enterprises.232.11.2.6.1.1.14.1 = STRING: "VcD_6f54796e7543",   
               SNMPv2-SMI::enterprises.232.11.2.6.1.1.15.1 = INTEGER: 2   
                 
               The two MIB OIDs in the trap above to analyze are:   
               enterprises.232.11.2.6.1.1.13.1   
               enterprises.232.11.2.6.1.1.15.1   
                 
               These OIDs will contain the following values when the Backup VC module has become the Primary:   
               cpqHoSWRunningConfigStatus : operational(5)   
               cpqHoSWRunningRedundancyMode : master(2)   
                 
            When upgrading from a pre-3.00 VC release, if Fibre Channel SNMP traps were defined with DNS type of the Trap Destination address, upon completion of the upgrade SNMP settings will not be applied to the VC-FC modules. Work-around: Edit any FC SNMP trap destinations, using the GUI or CLI, that have a DNS name for the trap destination and change the DNS name to an IPv4 address.   
            When Virtual Connect has assigned a Server Profile to a server, the ROM-Based Setup Utility (RBSU) can't modify the protocol configuration (iSCSI/FCoE) of any NIC (including the 551m), even if the NIC is not connected to a Virtual Connect module. Any protocol configuration changes must be made when the Server Profile is not assigned to the server.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.17
changelog:
  -     *Firmware Dependency:  
      **      OA: Minimum firmware version: 3.11 / Recommended version: 3.21   
              
            Generic firmware dependency is documented in the HP Virtual Connect Release Notes. It can be found in the 'User Guide' section, under the URL: _[http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=101&prodTypeId=3709945&prodSeriesId=3552695_](http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=101&prodTypeId=3709945&prodSeriesId=3552695)  
      
        
      **Problems Fixed:**  
            Resolved an issue where the primary VC module could not communicate with other modules due to a problem with the reverse DNS lookup when DNS is enabled in the VC infrastructure.   
            Resolved an issue where the VCM GUI was using HTTP instead of HTTPS.   
            Resolved an issue where changes in the SNMP configuration caused an outage.   
            Resolved an issue where updating gen numbers while creating or assigning a profile caused a NO-COMM state.   
            Resolved a GUI issue where renaming the associated network on the Edit Ethernet Network screen cleared the native property.   
            Resolved a GUI issue where clicking the Server Connections tab on the Ethernet Networks screen caused a popup message to appear stating that there are no server connections to display, even when server profiles with assigned networks existed.   
            Resolved a GUI issue where the Calculating Server Connections progress bar hung after clicking the Server Connections tab on the Ethernet Networks screen.   
            Resolved an issue where OA would enter NO-COMM state when multiple VC Enet modules were reset at the same time and then reconfigured. The VC Ethernet Module recovery algorithm has been optimized to recover Odd side modules and then Even side modules (previously was a full reset/recovery of all modules in parallel). Depending on configuration of the Domain, this will reduce or eliminate Network outage during a full enclosure recovery.   
            Resolved loss of FC connectivity when an 8Gb/24-Port VC-FC Module receives a multi-sequence frame from an in band Storage Management application (application was executing on a server within the c7000 enclosure). Resulted in a 8Gb/24-Port FC Module reset and loss of FC connectivity.   
            Resolved an issue when the VC-FC 24-Port Module would not recover from an NO-COMM state after an OA failover. The IP address for the FC Module was not being updated correctly, and blocking the proper communication with the Primary VC Module.  
            Resolved an issue where VCM reported a NO-COMM state for a VC-FC module, even though the VC-FC module was still responding to a ping command.   
            Resolved an issue where the VC 8Gb/24-port FC module firmware version information did not display correctly on the OA rack firmware page. This resolution requires OA version 3.30.   
            Resolved an issue with VC Manager failing to retrieve configuration generation number from VC Ethernet Module.   
            Resolved an issue where the network nativelan setting cleared after adding another network.   
            Resolved an issue where an hpvcm_deleteManagedObjects return code error occurred when deleting a profile.   
            Resolved an issue that delayed the startup time on an enclosure with eight Flex-10/FlexFabric modules.   
            Resolved a performance issue where adding a single network caused an update of all configured networks.   
            Resolved an issue where firmware details did not display on a Firefox browser window.   
            Resolved an issue where FCoE login took longer than expected when changing between fabrics.   
            Resolved an issue where the VCM CLI command "set enet-vlan" did not return an error for the command "set enet-vlan VlanTagControl=Tunnel SharedServerVlanId=true".   
            Resolved an HP Integrity BL8x0c i2 Series Server Blade issue where there were problems disconnecting Flex-10 ports with I/O modules that do not support Flex-10, which could result in disabled network ports appearing as enabled.   
            Resolved a GUI issue where titles on the Device Bay Summary screen were not displayed consistently.   
            Resolved an issue where an SNMP trap configuration with only FC traps selected could not have an associated set of severities.   
            Resolved an issue where an error was not indicated for login redistribution for a degraded/failed SAN in external connections.  
            Resolved a GUI issue for HP Integrity BL8x0c i2 Series Server Blades where the entries in the Server Ethernet Adapter Information table did not properly collapse and expand.  
            Resolved an issue found in an Integrity FlexFabric environment where the HP-UX boot path was lost while unassigning and reassigning a profile.  
            Resolved an issue for a race condition between module recovery and enclosure recovery when an enclosure was recovering from an enclosure NO-COMM condition.  
            Resolved an issue when recovering from a module NO-COMM state where the correct module state is properly tracked to avoid unnecessary failure for LANIO calls and GenNumber requests.  
            Resolved an FC module firmware issue where the VC 8Gb/24-port FC module firmware version is displayed as "Not Available" in OA, but VCM has the correct firmware version information.  
            Resolved an FC module firmware issue where the DHCP client in the VC 8Gb/24-port FC module firmware became corrupted, causing the FC module to stop responding to VCM, resulting in a NO-COMM state.  
            Resolved an issue when VC modules coming out of NO-COMM state, they may not be in sync with each other, which will result in unexpected additional module failures.  
            Resolved a restriction where customers need to put the VC domain in VCEM maintenance mode in order to get the support dump.  
            Resolved an issue where the GUI will state that the event manager registration has expired and then the user is logged out of the GUI unexpectedly.  
            Resolved an FC connection outage due to a failure of the Virtual Connect Flex Fabric primary module.  During the Backup Module recovery, the error caused a full Virtual Connect reset and recovery which created the outage.  
            Resolved an issue with growing memory utilization on HP VC Flex-10 10Gb Ethernet modules when Blades are in a PXE Boot loop.  
            Resolved an issue with a small memory leak found in stpd when handling of subport MED data update notices.  
            Resolved an issue where a VC domain will get into NO-COMM state after performing OA failover and then fail back.  
            Resolved an issue where the Private Networks filter rules were not updated when LAG (Link Aggregation Group) membership changes.  
            Resolved an issue where when a module recovers from NO-COMM state, the stacking links will show failed status even though there is no real operational problem.  
            Made adjustment for the Maximum RSS memory limit for graceful VC management process shutdown.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.18
changelog:
  -     *Firmware Dependency:  
      **     OA: Minimum firmware version: 3.11 / Recommended version: 3.30   
              
            Generic firmware dependency is documented in the HP Virtual Connect Release Notes. It can be found in the 'User Guide' section, under the URL: http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp contentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=101&prodTypeId=3709945&prodSeriesId=3552695 
      
        
      **Problems Fixed:**  
             Resolved an issue where a Virtual Connect Domain with large number of networks may experience an unstable network condition when a VC Ethernet module is restarted in one of the following circumstances:   
                * A power-cycle (Off/On) from the Onboard Administrator   
                * A reset/reboot from the Onboard Administrator   
                * A removal/reinsert into the Interconnect Bay


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.30
changelog:
  -     *New Features:**
      
        * Command Line Interface Telemetry - New CLI commands to troubleshoot Virtual Connect system and networking issues.
        * Network Access Groups for profile - Limits server profile access to networks that are defined within the group.
        * Simplified iSCSI boot setup - Automatically retrieve parameters from HP 4000 SAN solutions and attach to server profiles. Significantly reduces manual entries required.
        * Simultaneous tunneled and mapped VLAN connections - Unique VLAN flexibility supports best practice network requirements for virtualized servers.
        * Increased mapped VLAN capacity - up to 1000 VLANs SUS from 128 and up to 162 VLAN to down link from 28.
        * Enhanced port status - Feature to detect why a port is currently not in linked status.
        * GUI Profile Wizard support (Ethernet, iSCSI, FC, FCoE)
        * Native IE8 support
        * IGMPv3 Phase 1 IPv4 only (no support for source specific multicast)
        * OS Initiated Network Loop Detection and Prevention - uses Cisco PVST BPDUs
        * TACACS+/RADIUS role based security - User authentication, Command Authorization and Command loggings for network and storage teams.
        * Updated SNMP MIBs - Severity level added to all traps (alerts) to improve notification
        * Support for user-defined login screen notice (typically a security message)
        * Support for Log File Compression
        * Support connections for H3C DACs


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.30
changelog:
  -     The latest list of issues resolved can be found in the HP Virtual Connect
      Release Notes that can be found in the "User guide" section of the following
      URL**: **[http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?c
      ontentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=135&prodTypeId=
      3709945&prodSeriesId=4144084](http://h20000.www2.hp.com/bizsupport/TechSupport
      /DocumentIndex.jsp?contentType=SupportManual&lang=en&cc=us&docIndexId=64180&ta
      skId=135&prodTypeId=3709945&prodSeriesId=4144084)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.62
changelog:
  -     The latest list of issues resolved can be found in the HP Virtual Connect
      Release Notes that can be found in the following URL**:
      **<http://www.hp.com/go/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.10-2.1
changelog:
  -     *Corrected OpenSSL security vulnerability communicated in Security Bulletin HPSBMU02998 for CVE-2014-0160 known as "Heartbleed".**  
        
      The latest list of issues resolved can be found in the [VC 4.10 HP Virtual
      Connect Release Notes](http://h20565.www2.hp.com/portal/site/hpsc/template.PAG
      E/action.process/public/psi/manualsDisplay/?sp4ts.oid=4144084&javax.portlet.ac
      tion=true&spf_p.tpst=psiContentDisplay&javax.portlet.begCacheTok=com.vignette.
      cachetoken&spf_p.prp_psiContentDisplay=wsrp-interactionState%3DdocId%253Demr_n
      a-c03923055%257CdocLocale%253Den_US&javax.portlet.endCacheTok=com.vignette.cac
      hetoken).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.20-2.1
changelog:
  -     Corrected OpenSSL security vulnerability communicated in Security Bulletin
      HPSBMU02998 for CVE-2014-0160 known as "Heartbleed".  
        
      The latest list of issues resolved can be found in the HP Virtual Connect
      Release Notes that can be found in the "User guide" section of the following
      URL**: **[http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?c
      ontentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=135&prodTypeId=
      3709945&prodSeriesId=4144084](http://h20000.www2.hp.com/bizsupport/TechSupport
      /DocumentIndex.jsp?contentType=SupportManual&lang=en&cc=us&docIndexId=64180&ta
      skId=135&prodTypeId=3709945&prodSeriesId=4144084)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.21
changelog:
  -     Resolved an issue where some Virtual Connect Flex-10/10D IO Modules running HP
      Virtual Connect (VC) Firmware Version 4.20 or 4.30 may shut down due to a
      single instance of an erroneous high temperature reading from one of eight
      sensors on the module.  See VC Customer Advisory [c04459474](http://h20565.www
      2.hp.com/portal/site/hpsc/template.PAGE/public/psi/mostViewedDisplay/?javax.po
      rtlet=&javax.portlet.prp_efb5c0793523e51970c8fa22b053ce01=wsrp-navigationalSta
      te%3DdocId%253Demr_na-c04459474-1%257CdocLocale%253Den_US&javax.portlet.tpst=e
      fb5c0793523e51970c8fa22b053ce01&sp4ts.oid=5193137&ac.admitted=1412182531154.87
      6444892.492883150) for more information.  
        
      The latest list of issues resolved can be found in the HP Virtual Connect
      Release Notes that can be found in the "User guide" section of the following
      URL**: **[http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?c
      ontentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=135&prodTypeId=
      3709945&prodSeriesId=4144084](http://h20000.www2.hp.com/bizsupport/TechSupport
      /DocumentIndex.jsp?contentType=SupportManual&lang=en&cc=us&docIndexId=64180&ta
      skId=135&prodTypeId=3709945&prodSeriesId=4144084)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.31
changelog:
  -     Resolved the following issues:
      
        1. Some Virtual Connect Flex-10/10D IO Modules running HP Virtual Connect (VC) Firmware Version 4.20 or 4.30 may shut down due to a single instance of an erroneous high temperature reading from one of eight sensors on the module. See VC Customer Advisory [c04459474](http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/mostViewedDisplay/?javax.portlet=&javax.portlet.prp_efb5c0793523e51970c8fa22b053ce01=wsrp-navigationalState%3DdocId%253Demr_na-c04459474-1%257CdocLocale%253Den_US&javax.portlet.tpst=efb5c0793523e51970c8fa22b053ce01&sp4ts.oid=5193137&ac.admitted=1412182531154.876444892.492883150") for more information.  
      
      
        2. Updating to VC Firmware Version 4.30 may cause some or all networks to be unavailable which could result in all uplink ports showing as Linked-Standby. See VC Customer Advisory [c04422904](http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay?javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken&javax.portlet.prp_ba847bafb2a2d782fcbb0710b053ce01=wsrp-navigationalState%3DdocId%253Demr_na-c04422904-3%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.tpst=ba847bafb2a2d782fcbb0710b053ce01&ac.admitted=1413971313717.876444892.199480143) for more information.  
      
      
        3. Servers transmitting excessive pause frames may cause Virtual Connect uplink port to experience channel flapping, stacking link removal and server communication loss. See VC Customer Advisory [c02623029](http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?sp4ts.oid=1844065&spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c02623029-6%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken) for more information.  
      
      
        4. Any in-use network that was created in VC 4.2x or earlier may encounter a one-time network interruption when it is applied to an assigned server profile for the first time in VC 4.30. See VC Customer Advisory [c04492888](http://h20564.www2.hp.com/portal/site/hpsc/public/kb/docDisplay/?docId=emr_na-c04492888) for more information.  
      
      
        
      The latest list of issues resolved can be found in the HP Virtual Connect
      Release Notes that can be found in the "User guide" section of the following
      URL: [http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?conte
      ntType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=135&prodTypeId=3709
      945&prodSeriesId=4144084](http://h20000.www2.hp.com/bizsupport/TechSupport/Doc
      umentIndex.jsp?contentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId
      =135&prodTypeId=3709945&prodSeriesId=4144084)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.40
changelog:
  -     The latest list of enhancements can be found in the HP Virtual Connect Release
      Notes that can be found in the "User guide" section of the following URL**: **
      [http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentTyp
      e=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=135&prodTypeId=3709945&p
      rodSeriesId=4144084](http://h20000.www2.hp.com/bizsupport/TechSupport/Document
      Index.jsp?contentType=SupportManual&lang=en&cc=us&docIndexId=64180&taskId=135&
      prodTypeId=3709945&prodSeriesId=4144084)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.45
changelog:
  -     The latest list of enhancements can be found in the HP Virtual Connect Release
      Notes that can be found in the following URL**:
      **<http://www.hp.com/go/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.50
changelog:
  -     The latest list of enhancements can be found in the HPE Virtual Connect
      Release Notes that can be found in the following URL**:
      **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.50
changelog:
  -     The latest list of issues resolved can be found in the HPE Virtual Connect
      Release Notes that can be found in the following URL**:
      **[http://www.hpe.com/info/vc/manuals](http://www.hpE.com/info/vc/manuals)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.62
changelog:
  -     The list of enhancements in 4.62 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.62
changelog:
  -     The list of issues resolved in 4.62 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.63
changelog:
  -     The list of enhancements in 4.63 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.63
changelog:
  -     The list of issues resolved in 4.63 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.75
changelog:
  -     The list of enhancements in 4.75 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.75
changelog:
  -     The list of issues resolved in 4.75 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.80
changelog:
  -     The list of enhancements in 4.80 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.80
changelog:
  -     The list of issues resolved in 4.80 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.85
changelog:
  -     The list of issues resolved in 4.85 version can be found in the HPE Virtual
      Connect Release Notes at URL**: **<http://www.hpe.com/info/vc/manuals>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.3.0
changelog:
  - ENHANCEMENTS
  - hpasmlited now supports long IML messages. 
  - Added "show powermeter" command in hpasmcli. It shows the aggregate power consumption of the server. 

  - FIXES
  - Fixed the following issues: 
         1.hpasmcli -s "show server" command showed the L2 and L3 cache information incorrectly on multi processor systems. 
         2.hpasmcli showed incorrect fan numbers on HP ProLiant G6 servers. 
         3.hpasmxld segmentation fault when the HP Integrated Lights Out 2 (iLO 2)  broadcast storm occurs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.3.1
changelog:
  - FIXES
  - Fixed hp-health daemon to prevent soft lockups from occurring when the HP Integrated Lights-Out (iLO) controller becomes un  responsive due to network storm.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.3.2
changelog:
  - FIXES
  - Fixed a problem where if ambient temperature is very low, hpasmlited can incorrectly determine the system is over a tempera  ture threshold and improperly shut the system down.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.4.0
changelog:
  - ENHANCEMENTS
  - Added support for Integrated Lights-Out 3 (iLO 3). 
  - Added 'SHOW SEL' option in hpasmcli to display the System Event Log (SEL) contents on HP ProLiant 100 series servers. 
  - Updated libcpqci.so, which take advantage of upstream changes to hpilo, to provide better performance to applications, such  as SNMP agents like cmasm2d from hp-snmp-agents. 
  - Added 64-bit hpbootcfg utility.

  - FIXES
  - The Intel processor hyperthreading configuration can be enabled and disabled using hpasmcli on HP ProLiant G6 servers. 
  - Fix POSIX-compliancy issue with initscript. 
  - Avoid sending a SIGKILL to the health daemon, preventing ASRs that may occur on platforms (e.g. DL785) where hp-health shu   tdowns may take an extended amount of time.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.5.0
changelog:
  - ENHANCEMENTS
  - Split Advanced Server Recovery functionality into standalone hp-asrd service. For more information, execute 'man hp-asrd'.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.7.0
changelog:
  - ENHANCEMENTS
  - hpasm interface redesigned to use sockets in order to remove timeout related issues caused by message queue interface when   the system is in stress.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 10.0.0
changelog:
  - ENHANCEMENTS
  - Added support for HP ProLiant Gen9 Servers.

  - FIXES
  - HP Health may skip few lengthy POST error messages due to limitation of IPMI packet.


author: HPE Linux Development <Linux_SWdeliverables@external.groups.hp.com> 10.5.0
changelog:
  - ENHANCEMENTS

  - FIXES
  - iLO hpasmlited daemon crash after 2 iLO resets loops.
  - hpasmcli command fails to read the embedded NIC status shows as UNKNOWN.
  - Error logs seen in service hp-asrd status.


author:
  HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.0.19-2[rhel6u9], 2.0.19-1[For other OSs]

changelog:
  - Fix for configuration of RSS table with DCB
  - Enabled VF trust on RHEL 7.3
  - Added support for HPE Ethernet 10Gb 2-port 568i Adapter
  - Added SLES12SP2 support
  - Added RHEL7.3 support
  - Feature implementation for speading out interrupts and to use all rx queues and all cpus
  - Fix for NVM update process hangs on Linux at 88%


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.0.29-3
changelog:
  - Added support for HPE Ethernet 1Gb 2-port 368i Adapter
  - Added support for HPE Ethernet 1Gb 4-port 369i Adapter
  - Added support for HPE Ethernet 1Gb 2-port 368FLR-MMT Adapter
  - Added support for HPE Ethernet 10Gb 2-port 568FLR-MMT Adapter
  - Added support for HPE Ethernet 10Gb 2-port 568FLR-MMSFP+ Adapter
  - Added SLES12SP3 support
  - Added RHEL7.4 support


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.3.6-1
changelog:
  - This driver addresses an issue with branding string in RHEL7.4
  - This driver now fix the issue of LIS prevents switching back to the VF path in RHEL 7.3 guest
  - This driver now alllows to use ethtool -m on DAC with or without NPAR
  - This driver fixes the supported autoneg for devices with CRT_RETIMER
  - This driver now ignores locality when spreading vectors over CPUs
  - This driver now allows to change VLAN Tag Stripping
  - This driver now throws an error after attempt to advertise unsupported link mode
  - This driver now allows to set MTU value to more than 1500 in SLES12SP3 with Intel NICs
  - This driver fixes the issue of ethtool not showing up dual-speed modules advertisements
  - This driver fixes the issue of memory leak related to filter programming status
  - This driver fixes the issue of Flow Director Sideband rules do not update as expected
  - This driver fixes the issue of Could not change device features with Adapter Type SR-IOV passthrough and VSwitch VLAN Tagging Mode
  - This driver fixes the issue of VxLAN checksum offload counter increments without VxLAN tunnels present
  - This driver fixes the issue of kdump failure
  - Feature implemention for split PCI error reset handler
  - Feature implementation to return an error message when module that does not meet thermal requirements is plugged.
  - Feature implementation to add some hw_csum rx offload counters
  - Feature implementation to add wrap recovery mode.
  - Feature implementation to add ethtool_intersect_link_masks.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.4.6.1-4
changelog:
  - This driver fixes the issue of TX driver on SLES12SP2
  - This driver fixes the issue of Flow Director User documentation - README.TXT is not current
  - This driver fixes the issue of submodules updating
  - This driver fixes the issue of client close on Netdev down causing RDMA dev to unregister? 
  - This driver fixes the issue of unexpected queue selection messages observed during tx_timeout recovery? 
  - This driver now preserves promiscuous mode across resets


changelog:
  - Added RHEL6.10 Support.
  - Added RHEL7.5 Support.

author:
  HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.4.11-0[rhel6.10, rhel7u5], 2.4.6.1-7[For other OSs]


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.10.19.30-1
changelog:
  - This driver fix unexpected error message appears in dmesg when driver is loaded.
  - This driver fix VF 0 does not show via sysfs, and cannot be removed.
  - This driver fix 1g speed i40e_aq_run_phy_activity() from f/w reports lpi statistics always as 0


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.14.13-1.sles15sp1
changelog:
  - This driver fixes the issue of restoring all VF-d config on a VF reset.
  - This driver fixes the issue of mirror rule via VF-d.
  - This driver fixes the issue of VFD handler function prototypes.
  - This driver fixes the issue of assuming hardware is at default when that's not always true. 
  - This driver fixes the issue of not re-initializing properly in the case of CORE reset following PF reset timeout.
  - This driver fixex the issue of unknown NMI received and kernel crash when adding/removing VF to namespace repeatedly.
  - This driver fixes the issue of running 'ifconfig ethX mtu 2000' causes physial link down and failed to auto-recover, when we have set ' ethtool --set-priv-flags eth2 link-down-on-close on'.
  - This driver now introduce allow_untagged VF-d attribute.
  - This driver now add a helper function to validate a vf based on the vf id.
  - This driver now add a macro for checking if prog_attached exists.
  - This driver now add client register/unregister to prevent vsi.
  - Added RHEL7u6 Support.
  - Added SLES12SP4 Support.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.10.14-1
changelog:
  - This driver added the "Negotiated" string into the i40e_print_link_message() function. 
  - This driver fixes VF 0 failed opcode 3, when total cores =192( total threads =384, with Hyper threading enabled in BIOS)
  - This driver remove RDMA VF code from files including VF support.
  - This driver fixes the issue of reloading driver during resets loop causes platform to lose connection and trace call


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.10.16-1
changelog:
  - This driver add support to expose VF stats as part of PF interface ethtool stats.
  - This driver fix i40e Mirrors not clear after VF remove.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.10.19.81-1
changelog:
  - This driver export LPI time duration statistic info which can be observed by ethtool -S $pf
  - This driver fix an error message appeared like "0000 [#1] SMP PTI"


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.0.1-1
changelog:
  - Add SLES15 SP2 support
  - This driver fix system freezes when trying to create TCs on VF with no more VSIs available.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.3.5.3-1
changelog:
  - Added RHEL 6.8 support
  - Fix the issue of getting crash dump when loading igb module(modprobe igb)
  - Fix unable to disable the offload property in rhel6u6


changelog:
  - Added SLES12SP2 support
  - Added RHEL 7.3 support

author:
  HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.3.5.7-8[rhel6u9], 5.3.5.7-1[For other OSs]


changelog:
  - Added RHEL6.10 Support.
  - Added RHEL7.5 Support.

author:
  HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.3.5.19-0[rhel6.10, rhel7u5], 5.3.5.15-7[For other OSs]


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.3.5.42
changelog:
  - This driver fixes an issue of driver crash with ethtool command.
  - This driver fixes an issue of Klocwork hits.
  - Added RHEL7u6 Support.
  - Added SLES12SP4 Support.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups
changelog:
  .hp.com> 4.3.13-2
   - Fix the issue of First Virtual Function(VF) receiving a copy of Physical Function(PF)'s traffic
   - Added support for Multicast promiscous mode for trusted Virtual Functions


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.4.6-1
changelog:
  - Added RHEL 6.8 support
  - Fix the issue of unable to dynamically detect SFP module
  - Added support for Marvell PHY devices
  - Added new netdev operation to trust the Virtual Function
  - Added support to check and set the RSS hash and indirection table via ethtool -x/-X parameters	
  - Added new netdev op to allow user to enable/disable the ability of a specific VF to query its RSS Indirection Table and an RSS Hash Key
  - Fix the issue of packets being dropped as spoofed packets in SR-IOV mode
  - Fix the issue of macvlan interfaces not being able to get link, ixgbevf parent loses link
  - Fix the issue of ixgbe installation getting corrupted the system's ability to boot from SLES11SP4


author:
  HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.0.7-2[rhel6u9], 5.0.7-1[For other OSs]

changelog:
  - Added SLES12SP2 support
  - Added RHEL 7.3 support
  - Fix the issue of Vlan interface in RHEL 6.8 VM on RHEL6.8 host fails to get IP
  - Fix the issue of PHY stack trace and OS crash creating / allocating VFs.
  - Fix the issue of Transmit queue stuck [DCB enabled]
  - Fix the issue of NULL pointer dereference when enabling SRIOV
  - Fix the issue of cannot set MACVLAN if MAC is set by PF, when VF is trusted


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.2.1-4.rhel7u4
changelog:
  - Added support for HPE Ethernet 10Gb 2-port 562FLR-T Adapter
  - Added support for HPE Ethernet 10Gb 2-port 562T Adapter
  - Added SLES12SP3 support
  - Added RHEL 7.4 support
  - Fix the issue of sriov_totalvfs reporting incorrect number of supported VFs
  - Fix the issue of RHEL6.9 64 bit is not able to create Virtual Functions with the sysfs command


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.3.3-1
changelog:
  - This driver updated branding strings from HP to HPE for legacy adapters 
  - This driver fixes the issue of Unable to automatically get link after swapping SFP+ modules of different speeds 
  - This driver fixes the issue of IPV6 magic packet can't wake up
  - This driver fixes the issue of unable to set MTU value more than 1500 in SUSE12SP3 with Intel NICs
  - This driver fixes linux Kernel panic occurs when assigning an IP address on HVL system with non existing PHY


changelog:
  - Added RHEL6.10 Support.
  - Added RHEL7.5 Support.

author:
  HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.3.7-0[rhel6.10, rhel7u5], 5.3.5.1-8[For other OSs]


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.6.4-1
changelog:
  - This driver fixes an issue of Infinite recursion in device shutdown path due to a corner case when PCIe link was down
  - Fix the issue of typo in ethtool stats
  - Added RHEL7u7 Support.
  - Added RHEL8 Support.
  - Added SLES15SP1 Support.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 3.23.0.79
changelog:
  - Added SLES 12 support
   - Added RHEL 6.6 support
   - Fixes the issue of TX Unit hang which occurs when re-plugging of  network cable while passing traffic on VMs(using VFs)
   - Fixes incorrect reporting of sriov values under sysfs
   - Fixes the issue ixgbe driver causing keyboard delay when DAC Cables are used


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.0.3-1
changelog:
  - Added RHEL 7.1 support
   - Added SLES11SP4 support
   - Fixed the issue of VXLAN offload tx-udp_tnl-segmenation not getting enabled
   - Made changes to use dma_rmb when accessing RX descriptors.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.1.5-6
changelog:
  - Added SLES12SP1 support
   - Added RHEL 7.2 support
   - Used new skb_vlan_tag_* functions instead of old vlan_tx_tag_* functions.
   - This driver addresses an issue where the link speed reported by the HPE Active Health System (AHS) is incorrect.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 5.6.4-1
changelog:
  - This driver fixes the issue of an infinite recursion in device shutdown path due to a corner case when PCIe link was down.
  - This driver fixes the issue when configuring MTU on VF in Guest OS would be failed.
  - Added RHEL7u7 Support.
  - Added RHEL8u0 Support.
  - Added SLES15SP1 Support.


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 3.1.2-2
changelog:
  - Fix the issue of packet loss in Virtual Functions(VF) in cases where Physical Function(PF) interface is brought up after VF.
   - Added support for Multicast promiscous mode for trusted Virtual Functions


author:
  HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.0.5-2[rhel6u9], 4.0.5-1[For other OSs]

changelog:
  - Added SLES12SP2 support
  - Added RHEL 7.3 support
  - Fixed the issue of installing ixgbevf corrupts ability of virtual machine to boot from SLES 11 SP4

   Tue Jun 21 2016 HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 3.2.2-1
  - Added RHEL 6.8 support
  - Fix the issue of setting of invalid MTU
  - Added support for ethtool RSS get/set functionality
  - Fix the issue of No error generated if untrusted VM user tries to set user defined VF MAC address


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.2.1-4.rhel7u4
changelog:
  - Added support for HPE Ethernet 10Gb 2-port 562FLR-T Adapter
  - Added support for HPE Ethernet 10Gb 2-port 562T Adapter
  - Added SLES12SP3 support
  - Added RHEL 7.4 support
  - Fix the issue of sriov_totalvfs reporting incorrect number of supported VFs


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.3.2-1
changelog:
  - This driver fixes the issue of unable to set MTU value more than 1500 in SUSE12SP3 with Intel NICs


changelog:
  - Added RHEL6.10 Support.
  - Added RHEL7.5 Support.

author:
  HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.3.5-0[rhel6.10, rhel7u5], 4.3.3.1-8[For other OSs]


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 2.16.0.43
changelog:
  - Added SLES 12 support
   - Added RHEL 6.6 support
   - Added netconsole/netpoll support for Virtual Function interface
   - Fixed vlan support issues on linux kernels >= 3.10 which was broken due to recent kernel changes
   - Fixed issue of ifconfig TX stats incrementing without traffic present on VF interface
   - Fixes the issue of TX Unit hang which occurs when re-plugging of  network cable while passing traffic on VMs(using VFs)


author: HP Linux SW Deliverables <Linux_SWdeliverables@external.groups.hp.com> 4.6.2-1
changelog:
  - This driver fixes the issue of an infinite recursion in device shutdown path due to a corner case when PCIe link was down.
  - This driver fixes the issue of Link lost in VM on ixgbevf when restoring from freeze or suspend.
  - This driver fixes the issue when configuring MTU on VF in Guest OS would be failed.
  - Added RHEL7u7 Support.
  - Added RHEL8u0 Support.
  - Added SLES15SP1 Support.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.4.0
changelog:
  - 8.4.0 release (Severity: Medium)
  - ENHANCEMENTS
  - Added support for Integrated Lights-Out 3 (iLO 3)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 10.0.0
changelog:
  - ENHANCEMENTS
  - Added support for HP ProLiant Gen9 Servers.

  - FIXES
  - When SNMP community string is configured as other than public in snmpd.conf file, all the webapp data is now populating in HP System Management Homepage (SMH) for Red Hat Enterprise Linux (RHEL) 6.5.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.3.0
changelog:
  - ENHANCEMENTS
  - Added new 6069 trap upon AC Power loss. Also, the MIB cpqHeFltTolPowerSupplyErrorCondition will show the error information   if the power supply supports error reporting.
  - The agents now retrieve the Power supply Serial number from Type 39 SMBIOS record if it is present.
  - The agents now display the negative temperature readings correctly if it is reported by the temperature sensors.
  - The cmahostd agent now updates the PowerPIC firmware version information in the cpHoFwVerTable.
  - Updated the SIM event severity to .informational. after the secure erase is completed.
  - Added support for HP NC362i Integrated Dual Port.

  - FIXES
  - The cmapeerd agent logs the error .sendto() failed. to cma.log file.
  - The DIMM type displayed incorrectly on HP ProLiant BL460c G5.
  - The cmahealthd agent sent the 6036 trap instead of 6035 trap upon fan failure.
  - The port numbers displayed incorrectly for HP NC532i Dual Port 10GbE Multifunction BL-c Adapter.
  - The Part Number displayed incorrectly.
  - The cmanicd crashed after creation of multiple VLAN, disconnect/connect of NIC link.
  - The System Id displayed incorrectly on the System Management Homepage (SMH).
  - The blink drive LED feature for HP Smart Array B110i SATA RAID Controller.
  - The embedded Broadcom SATA controller was not detected on System Management Homepage (SMH).
  - The multipath status was displayed as "unknown" when a drive failed.
  - The failed logical drive status displayed incorrectly during an array move, expansion or shrink.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.4.0
changelog:
  - ENHANCEMENTS
  - Added support for HP ProLiant  G7 Servers.
  - Added support for Integrated Lights-Out 3 (iLO 3).
  - Included a document called  HP_SNMP_Trap_Guide.txt  that  describes the Linux SNMP trap ID messages generated by the agent
  - Improvements to distribution identification including more consistent output and increased support for community and region  al   distributions.
  - Added support for Solid State Drives.
  - Added support for HP StorageWorks 2000sa Modular Storage Array and HP StorageWorks MSA2012sa/ MSA2312sa/  MSA2324sa when co  nnected to HP SC08Ge Host Bus Adapter.
  - Added support and trap support (link up/down message) for the following HP NC-Series:
       .	HP NC542m Dual Port Flex-10 10GbE BL-c Adapter
       .	HP StorageWorks CN1000E Dual Port Converged Network Adapter
       .	HP NC550m Dual Port Flex-10 10GbE BL-c Adapter
       .	HP NC551m Dual Port FlexFabric 10Gb Converged Network Adapter
       .	HP NC551i Dual Port FlexFabric 10Gb Network Adapter
       .	HP NC362i Integrated Dual Port Gigabit Server Adapter
       .	HP NC362i Integrated Dual Port BL-c Gigabit Server Adapter

  - FIXES
  - Modified the 6064 trap implementation to reflect the correct error.
  - Removed unnecessary information in cmahostd related to bonding driver, in order to improve performance.
  - Fixed an issue to display the Port number of Physical drives connected to Fiber Channel controller.
  - Fixed an issue to display Parity group count for RAID 50 and RAID 60 Logical drives.
  - Modified the script to get the NIC ports details from /sys/class/net.
  - Fixed an issue where wrong physical address is displayed on SMH, resolution was provided by checking for pcidevice informat  ion instead of subsytem device information.
  - Fixed an issue where SNMP Alerts/IMA trap were not received by HP SIM.
  - Fixed an issue where junk characters and misalignment on the console during reboot by adding new line in stop section.
  - Fixed an issue where Linux SMH shows incorrect bay/port information by adding support for virtual port.
  - Fixed an issue where cmanicd is filling /var/log/messages via setroublesoot, resolved by modified selinux policy package (H  Pcmanic.pp).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.5.0
changelog:
  - ENHANCEMENTS
  - Enhanced HP SNMP Agents to retain default permission and ownership of snmpd.conf file.
  - Added support and trap support (link up/down message) for the following HP NC-Series:
         . HP NC551m Dual Port FlexFabric 10Gb Adapter
         . HP NC551i Dual Port FlexFabric 10Gb Adapter
         . HP NC365T 4-port Ethernet Server Adapter
         . HP NC543i 10Gb 2-port  4X Flex-10  QDR Server Adapter
         . HP NC553m 10Gb 2 port FlexFabric Converged Network  Adapter
         . HP NC552m 10Gb 2 port FlexFabric Converged Network Adapter
         . HP NC553i 10Gb 2 port FlexFabric Converged Network Adapter
         . HP NC552SFP 2-port 10Gb Server Adapter
         . HP StorageWorks CN1000Q Dual Port Converged Network Adapter
         . HP NC525m 10Gb 2 port FlexFabric Converged Network Adapter

  - FIXES
  - Fixed an issue where unwanted messages getting logged in the cma.log was resolved by removing the fprintf for virtual port.
  - Fixed an issue where cmanicd leaves trail of zombie lspci processes by modifying lspci usage in port_map.c and redirected o  utput to /dev/null.
  - Fixed issue not to display driver messages on console for HP B110i Smart Array controller.
  - Fixed issue on CmaX, which displayed parsing error message on the syslog during agents reboot


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.6.0
changelog:
  - ENHANCEMENTS
  - Added support for the MIBs in the Power Supply Table.
  - Added support for the MIB that specifies the version of Insight Management Agents running on the system.
  - Added support for the HP NC552m 10Gb 2-port FlexFabric Converged Network adapter.

  - FIXES
  - Addressed the tape drive not being displayed on the SMH on few configurations.
  - Displayed the placement correctly for the failed drive after reboot.
  - On Cmax, net-snmp displayed duplicate registration message on the syslog.
  - Modifications are done in code to support the HP NC542m for which PCIID information is the same for both the ports.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 8.7.0
changelog:
  - ENHANCEMENTS
  - Added support to display "N/A" for non reactive thermal sensors instead of "0" value.
  - Added support to expose firmware version details for FMP, FPGA and cPLD (XNC) firmware.
  - Added support to report USB key/SD card information.
  - Provided greater than 2TB physical disk support for smart array and dumb SATA chipsets.
  - Added new accelerator error code: "Flash Backed Cache Erasing Flash Memory".
  - Added Physical Disk Temperature support.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 10.0.0
changelog:
  - ENHANCEMENTS
  - Added support for HP ProLiant Gen9 Servers.

  - FIXES
  - cmafcad daemon appears to cause segmentation fault.
  - cmastdeqd daemon appears to cause segmentation fault when removing USB key.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hp.com> 10.5.0
changelog:
  - FIXES
  - Cmahostd does not ignore nfs4 mount points.
  - cmahostd triggers NFS auto-mounting and resulted in performance problem.
  - Files in directories under /var/spool/compaq/hpasm/registry/ have SGID bit set removed.


author: Prashant Sreedharan <prashant@broadcom.com> - 1.0.14
changelog:
  - CQ73669: No support for 5717C0 devid (Severity: Minor)
  - CQ73746: tg3sd fails to run on RH7.0 (Severity: Minor)
  - hp-tg3sd-x.x.x.rpm fails to install on SLES11sp3 (Severity: Minor)


author: Siva Reddy Kallam <siva.kallam@broadcom.com> - 1.0.19
changelog:
  - CTRL-20577: tg3sd does not run under RHEL 7.2 (Severity: Minor)
  - CTRL-20998: 330i Network information missing in AHS (Severity: Minor)


author: Rajeshwari <stsd-ailsa@hp.com> 2.2.0-2
changelog:
  - Extension of -w option to include more iLO configuration
  - Fixed an issue where previous version of hponcfg failed to support older iLO Channel Interface drivers


author: Rajeshwari <stsd-ailsa@hp.com> 3.0.0-1
changelog:
  - Support for iLO3, iLO3 identification
  - Fixed an issue related to dynamic linking of hponcfg with libcpqci.so to resolve rdp related issue.


author: Sivakumar A <sivakumar.alagumalai@hp.com> 4.2.0-0
changelog:
  - v4.2.0 is mainly targeted for iLO4 1.30, iLO3 1.60 and iLO2 2.20
  - Created 32 bit and 64 bit RPM Packages to load shared library from hp-helth agent as libcpqci.so (in case of 32bit OS) and libcpqci64.so (in case of 64bit OS)


author: Naveen N <naveen.n2@hpe.com> 5.4.0-0
changelog:
  - Changes include to select correct libssl.so file when multiple Openssl installed (32-bit and 64-bit)


author: Hewlett-Packard Development Company, L.P. 7.1.0
changelog:
  - Improved trust mode during upgrade
   - Fixed group configuration management during Replicate Agents Settings (Severity: Serious)
   - Improved SMH service management
   - Fixed PHP files to avoid crash (Severity: Serious)
   - Improved webapp configuration files
   - Fixed SMH supporting DLLs to avoid version conflicts (Severity: Serious)
   - updated properties of SMH setup file
   - Updated secured handling of HTTP response
   - Updated Libxml2 to version 2.7.8
   - Updated PHP to version 5.3.10
   - Updated Curl library to version 7.24.0
   - Updated OpenSSL to version 1.0.0h
   - Updated SMH service runs with managed privileges
   - Enable support of Windows 2008 R2 Sp1 - Server Core
   - Enable support of Windows Server 8 (Beta)
   - Enable support of Windows Multipoint Server 2011 for x64
   - Enable support of Microsoft Windows Small Business Server 2011 for x64, Standard and Essentials
   - Updated usability of IP restrictions with SMH Command Line Interface
   - Updated information provided on webapp availability & loading statistics
   - Added support for Firefox 9.0 & 10.0

   * Thu Oct 13 2011 Hewlett-Packard Development Company, L.P. 7.0.0
   - Fixed SMH improperly displayed an invalid certificate warning when restarted, even on a fresh install. (Severity: Medium)
   - Added a command line option to modify the local and state information in the SMH PKCS (Public-Key Cryptography Standards) data
   - Added secured handling of HTTP request and response
   - Added support for Firefox 6.0, 7.0, 8.0 and Internet Explorer 9.0
   - clarified the log messages
   - Improved handling of command Line Interface options
   - Improved handling of IP fields
   - Improved handling of memory resources
   - Improved handling of revoked trusted certificate
   - Improved handling of SMH configuration file and settings
   - Improved CLI options, for easier management of SMH configurations
   - Updated the HTTP links
   - Updated Apache to version 2.2.21
   - Updated Curl library to version 7.21.7
   - Updated OpenSSL to version 1.0.0e
   - Updated PHP to version 5.3.8


author: Hewlett-Packard Development Company, L.P. 7.1.1
changelog:
  - On some Non-English Windows Operating Systems, user is not able to login into SMH 7.1.0. This version will solve this problem (Severity: Critical)
   - Improved security features of PHP (Severity: Critical)


author: Hewlett-Packard Development Company, L.P. 7.1.2
changelog:
  - Improved security features
   - Improved logging on few Operating Systems
   - Enable support of Red Hat Client 5.8
   - Updated OpenSSL to version 1.0.1c (Severity: Critical)
   - Updated PHP to version 5.3.14 (Severity: Critical)
   - Improvement in RPM packaging


author: Hewlett-Packard Development Company, L.P. 7.2.0
changelog:
  - Updated Apache to version 2.4.3 (Severity: Critical)
   - Improved logging on few Operating Systems
   - Improvement in Certificate management
   - Added support for Firefox ESR 17.0 and Internet Explorer 10.0
   - Enable support for Transport Layer Security (TLS) protocol 1.1 / 1.2
   - Improved User Interface for Online Help
   - Improved CLI options for easier management of SMH configurations
   - Secured handling of HTTP communication


author: Hewlett-Packard Development Company, L.P. 7.2.2
changelog:
  - Updated the following components
     PHP to version 5.4.11
     Curl to version 7.28.1
   - Enable support of SUSE Linux Enterprise Server 11 SP3


author: Hewlett-Packard Development Company, L.P. 7.3.0
changelog:
  - Enabled Simplified Chinese localization
   - Updated the following components
     Apache to version 2.4.6
     Libxml2 to version 2.9.1
     OpenSSL to version 1.0.1e
     Curl to version 7.32.0
     PHP to version 5.5.2
   - Packaged zlib 1.2.8 with SMH


author: Hewlett-Packard Development Company, L.P. 7.3.1
changelog:
  - Enabled support of 2048 & 4096 bit certificate for Single Sign-On (SSO)
   - Enabled FQDN (Fully Qualified Domain Name) for the CN (Common Name) field in the self-signed certificate & CSR (Certificate Signing Request)


author: Hewlett-Packard Development Company, L.P. 7.4.0
changelog:
  - Enabled support for Red Hat Enterprise Linux 7 
   - Updated the following components 
     PHP to version php-5.5.13 
     Curl to version curl-7.35.0
     Openssl to version openssl-1.0.1h
   - Improved SMH to use the system resources efficiently
   - SMH Plugin integration is modified
   - Enabled Japanese localization in SMH smart component installer
   - Removed files related to Namazu
   - Removed the checks for ZLIB installation


author: Hewlett-Packard Development Company, L.P. 7.4.1
changelog:
  - Updated the following components
     PHP to version php-5.5.18
     Curl to version curl-7.38.0
     Openssl to version openssl-1.0.1j
   - Disabled SSLv3 Protocol
   - SMH is been improvised with respect to security vulnerabilites


author: Hewlett-Packard Development Company, L.P. 7.5.0
changelog:
  - Updated the following components
     PHP to version php-5.5.23
     Openssl to version openssl-1.0.1m


author: Hewlett-Packard Development Company, L.P. 7.5.2
changelog:
  - Updated the following components
     PHP to version php-5.6.11
     Openssl to version openssl-1.0.2d
     Curl to version curl-7.42.1
   - SMH is been improvised with respect to security vulnerabilites


author: Hewlett-Packard Development Company, L.P. 7.5.4
changelog:
  - HP SMH self-signed certificate signature is changed to SHA-2
   - SMH is been improvised with respect to security vulnerabilites


author: Hewlett Packard Enterprise Development L P. 7.5.5
changelog:
  - HPE Rebranding changes
   - Updated the following components
     PHP to version php-5.5.31
     cURL to version curl-7.47.0
     OpenSSL to version openssl-1.0.2g
     Libxml2 to version libxml2-2.9.3
   - SSL protocol is now configurable through smhconfig cli
   - SMH is been improvised with respect to security vulnerabilites


author: Hewlett Packard Enterprise Development LP 7.6.0
changelog:
  - Updated the following components
     PHP to version php-5.5.38
     cURL to version curl-7.49.1
     OpenSSL to version openssl-1.0.2h
     Libxml2 to version libxml2-2.9.4
   - SSL Cipher Suite is set to TLSv1.2 as default
   - SMH is been improvised with respect to security vulnerabilites
   Upgrade Requirement: Recommended ? HPE recommends users update to this version at their earliest convenience.


author: Hewlett Packard Enterprise Development LP 7.6.1
changelog:
  - Updated the following components
     PHP to version php-5.6.27
     OpenSSL to version openssl-1.0.2k
     Apache to version httpd-2.4.25
   - SMH is been improvised with respect to security vulnerabilities
   Upgrade Requirement: Recommended ? HPE recommends users update to this version at their earliest convenience.


author: Hewlett Packard Enterprise Development LP 7.6.3
changelog:
  - Updated the following components
     PHP to version php-5.6.30
     OpenSSL to version openssl-1.0.2k
     Apache to version httpd-2.4.25
   - SMH is been improvised with respect to security vulnerabilities
   Upgrade Requirement: Recommended ? HPE recommends users update to this version at their earliest convenience.


author: Hewlett Packard Enterprise Development LP 7.6.4
changelog:
  - Supported the SLES 15 OS
   Upgrade Requirement: Recommended ? HPE recommends users update to this version at their earliest convenience.


author: Hewlett Packard Enterprise Development LP 7.6.6
changelog:
  - Updated the following components
     PHP to version php-5.6.30
     OpenSSL to version openssl-1.0.2k
     Apache to version httpd-2.4.41
   - SMH is been improvised with respect to security vulnerabilities and Supported the RHEL 8 OS
   Upgrade Requirement: Recommended ? HPE recommends users update to this version at their earliest convenience.


author: Broadcom Build Environment
changelog:
  -Added Linux SRIOV support
  -Added iSCSI & FCoE HBA support for specific HP adapters and devices
  -Added VC4.10 support
  -Added BCV support
  -When GRO setting changes while LRO is enabled, don't reload as LRO takes precedence.
  -Allow UDP tunneling offload
  -Enable IPGRE RSS by default
  -Support different GRE RSS modes.


author: Broadcom Build Environment
changelog:
  -Add RH5.10 support.
  -Add RH6.5 support.
  -FC-TAPE - Host responds early to a requested resend delay - Linux (70101)
  -SLES11 MEZ75 IO halt with Nexus reboot tests (70728)
  -SLES 11 blade loses all targets from BLOM port during fabric uplink add/remove (70187)
  -KVM gso and gro are not working on hv and vm as expected (70506)
  -SRIOV mtu toggle failure (70530)
  -SRIOV hv reboots on pf toggle with vfs passed through on it. (70531)
  -Guest OS dosent boot after attaching VF in RHEL6.3x64bit for 57840 device. (68426)
  -[NET]SUT reboot&MCE report when create 30th/31st VF on 57810 device on SLES11 SP2. (69263)
  -RH Cert - RH5 | U8 | v7-1.5-33 | 57810 | Flex Network Test failed. (70427)
  -BACS 16.2.0: Show ETS/Priority Tagging/PFC as operational when DCBX is disabled on the switch side. (69690)
  -Incorrect port value is displayed for connected/unconnected ports of 57810 for RHEL5.9 64bits. (68627)
  -VFs are not getting created for Broadcom adapters in RHEL5.10 OS. (71456)


author: QLogic Build Environment 7.12.37.1
changelog:
  - added RH5.11 support.
  - added RH6.6 & RH6.7 support.
  - added RH7.0 & RH7.1 support.
  - added SLES11-SP4 & SLES12 support.
  - added VLAN filtering offload support.
  - added Debian GNU/Linux 7 (wheezy) support.
  - In RHEL7.0 and 7.1, bnx2x will be rolled back to inbox after system reboot (80071).
  - SRIOV : MAC address change inside VM is not allowed unless interface is down (80309).
  - RH7.x:  Tunneling offload is not enabled (79269).
  - self test fails on 20G adapter (79295).
  - VF interface vlan-filtering stopped working (79365).
  - Fail to force link speed other than 20G in KR2 (77841).
  - Incorrect asymmetric flow-control behavior (75504).
  - Dynamic VF enumeration fails for 578xx adapter in SLES11 SP4 (78590).
  - Inner-to-outer vlan priority mapping doesn't work (RH6.x [pre 2.6.38 kernels]).
  - Packets from a VF with pvid configured which were sent with a different vlan were transmitted instead of being discarded.
  - UDP packets cannot pass to the upper application (5709).
  - Out of memory issue when the adapter is reset (5709).
  - iSCSI offload: Driver displaying incorrect remote port (77842).
  - FCoE offload: Initiators failed FLOGI on SLES 11 SP4 RC1 (79704).


author: QLogic Cavium Build environment
changelog:
  - Version 8.18.18.0
  - Added missing support to configure 1G speed via ethtool
  - Fixed calculation of number of ooo rx buffers and limit to 16K

  - Version 8.18.17.0-1
  - iWARP - Handle flush completion on unaligned ll2 connection
  - Add dp_module, dp_level as modparams
  - Add Kconfig file for upstream builds

  - Version 8.18.16.0-1
  - Fix missing return error code check on call to qedi_setup_int
  - Modify different module params
  - Add log message in the driver unload path
  - Fail all non-timesync related ioctls

  - Version 8.18.15.0-1
  - Added wwpn and wwnn to the FCoE dev-info
  - Validate chap and mutual chap auth correctly

  - Version 8.18.14.0-1
  - Fix error handling flow in TX path
  - Fix error handling flow in RX path
  - Implement get_protocol_tlv_data callback


author: QLogic Corp <support@qlogic.com> 10.02.01.00.a14-k1-1
changelog:
  - 10.02.01.00.a14-k1 BH 11/06/2020

  - ER146725: eDIF another driver panic running script: ./test_target_no_unload.sh
  Change: qla2xxx: Fix crash in qla_nvme_abort_set_option.

  - ER147771: Call Trace while shutting down the adapter ports (LINK DOWN).
  Change: qla2xxx: Handle aborts correctly for port undergoing deletion.

  - ERXXXXXX: qla2xxx: Add scsi_change_queue_depth to slave configure.

  - 10.02.02.00.a13-k1 BH 10/28/2020

  - ER147600: Cisco: rpd ELS cmd fail to fetch the speed capabilities
  Change: qla2xxx: Used correct rdp spec, which was broken during code clean-up.

  - ER147695: FC-NVMe target discovery fails when initator wwpn < target wwpn in an N2N (Direct Attach) config
  Change: qla2xxx: fix N2N + NVME connect retry fail

  - ER147832: Issue with uSCM Linux with QCC CLI for some configuration
  Change: qla2xxx: Show event severity only when device state is congested.

  - ER147824 : scmr_stat sysfs node runs out of memory
  Change: qla2xxx: Come up with a compact version of scmr_stat

  - ER147823: NVMe IO is not getting throttled up or down.
  Change: qla2xxx: Enable throttle control for NVMe targets for Peer Congestion.

  - ERXXXXXX: qla2xxx: Count tgt short term link if link comes back before dev_loss_tmo.
  - ERXXXXXX: qla2xxx: Correct the check for fcport while displaying target counters.
  - ERXXXXXX: qla2xxx: Change trigger for host short term link down to dev loss tmo.
  - ERXXXXXX: qla2xxx: Move an SCM log under a debug level.
  - ERXXXXXX: qla2xxx: Set vendor_rsp[0] value.
  - ERXXXXXX: qla2xxx: Make throttling messages more informative.

  - 10.02.02.00.a12-k1 SK 10/15/2020
  - ER147625: NVMe IO's are failing with Read/Write after LIP reset.
  Change: qla2xxx:Return EBUSY until the remote port delete finishes.

  - ER147653: Target side strongswan start/stop, make initiator crashed.
  Change: qla2xxx: edif: v2 fix double bsg done.

  - ER147791: USCM: clear option is not clearing hba alarm/warning, or clear cong or nvme target stats.
  Change: qla2xxx: Clear Sev and NVMe Target Stats.

  - ER147793: USCM: Throttling has wrong throttling up info and event period is not honored.
  Change: qla2xxx: Fix Throttling algorithm regression.

  - ER147759: NVMe Admin commands are getting throttled and causing admin queue failures.
  Change: qla2xxx: Throttle NVMe I/O commands only.

  - ERXXXXXX: qla2xxx: edif: fix aes_gmac mode.
  - ERXXXXXX: qla2xxx: edif: v2: standardize on port_id_t for bsg api.
  - ERXXXXXX: qla2xxx: edif: fix 4byte align.
  - ERXXXXXX: qla2xxx: edif: fix ELS meta data.
  - ERXXXXXX: qla2xxx: Clear Congestion State/Throttling during chip Reset.
  - ERXXXXXX: qla2xxx: Clear SCM Severity as part of SCM Stats Clear.

  - 10.02.00.02.a11-k1 BH 10/09/2020
  - ER147734 : Lip reset on the isolated port causes server crash
  Change: qla2xxx: Don't allow FW, MPI and lip reset on isolated port.

  - ER147479 - PPC BE RH7.6 - qla2xxx driver loading - machine crashed.
  Change: qla2xxx: Fixes for big endian machines

  - ER147646: Call Trace observed while validating a MPI Pause test scenario. 
  Change: qla2xxx: Correct the WARN_ON check in qla_nvme_abort_set_option.

  - ER147615: Throttling does not work with low I/Os.
  Change: qla2xxx: Check and round off fractional I/Os to 1 on ISP 27xx/28xx Series Adapters

  - ERXXXXXX: qla2xxx: List NVMe targets under scmr_stats on ISP 27xx/28xx Series Adapters
  - ERXXXXXX: qla2xxx: Don't check for port isolation during abort isp.
  - ERXXXXXX: qla2xxx: SCM: Turn off SCM port parameter update mailbox command.
  - ERXXXXXX: qla2xxx: Fix I/O failures during remote port toggle testing

  - 10.02.00.02.a10-k1 BH 09/25/2020
  SCM Changes:
  - ERXXXXXX:
  Changes - qla2xxx: Clear Congestion state when an RSCN is received/target is torn down.
  qla2xxx: throttling algorithm improvement.
  qla2xxx: Add throttling support for NVMe targets.

  EDIF Changes:
  - ERXXXXX: LUN loss on ipsec stop/start on target side.
  Change: save Nport on receive of PLOGI
  - ERXXXXX: fix ELS receive collision between physical and NPIV hosts.
  Change: remove erroneous source Nport ID search.

  - ER147570: FCP Performance Drop in latest driver for smaller IOs size.
  Change: qla2xxx: Change WQ_UNBOUND to WQ_MEM_RECLAIM. WQ_MEM_RECLAIM : wq is guaranteed to have at least one execution context regardless of memory pressure.

  - ER147632: QLE2774: RHEL 8.2 System crashes while upgrading he FW from 9.6.0 to 9.6.1 with QCC CLI build 12
  Change: qla2xxx: Fix system crash on nvme abort path by checking sp of aborting command before accessing it.

  - ER147418: server crash seen when trying to capture the debugfs stat on isolated port.
  - ER147645: System panic while trying to capture debugfs stats for EED.
  Change: qla2xxx: Check rport before accessing target number.

  - ER147632: Fix potential stale mem access
  Change: remove stale sp pointer reference

  - CQXXXXXX: FPIN events are not readily decodable.
  Change: qla2xxx: Make FPIN events prints human readable.

  - ER146879: Add support to clear SCM Stats
  Change: qla2xxx: Added support to clear SCM/SCMR Stats on ISP 27xx/28xx Series Adapters

  - ERXXXXXX: qla2xxx: Allow get host stat during reset and sync reset.
  - ERXXXXXX: qla2xxx: Set reset_cmd_err_cnt on reset failure only.
  - ERXXXXXX: qla2xxx: Add isolated flag and return EPERM on isolation.
  - ERXXXXXX: qla2xxx: Count short term link if link comes back in 10 sec.
  - ERXXXXXX: qla2xxx: Don't check for fw_started while posting nvme command.
  - ERXXXXXX: qla2xxx: Pass irq_offset to blk_mq_pci_map_queues API.
  - ERXXXXXX: qla2xxx: lockdown: fix stale sp access.
  - BZ1868688: qla2xxx: tear down session if FW say its down.

  - 10.02.00.02.a9-k1 BH 09/03/2020
  - ER147554 - sg_reset appears hung iterating over too many Qpairs.
  Change - qla2xxx: limit interrupt vectors to number of cpu.

  - ERXXXXX - qla2xxx: klocwork: Fix Bit field 'mpi_-' has one bit and is signed.

  - ERXXXXX - qla2xxx: Change post del message from debug level to log level.

  - ERXXXXX - qla2xxx: lockdown: fixup - Change error response as per API test.

  - ERXXXXX - qla2xxx: Fix map_queue interface to use the correct blk-mq call.

  - ERXXXXX - Added Structural changes for SCM Phase 2 support.
  Change : qla2xxx: Update structure definitions for SCM to support backward compatibility.

  - 10.02.00.02.a8-k1 BH 08/30/2020
  - ERXXXXXX - Fix point-to-point (N2N) device discovery issue.
  Change - qla2xxx: Fix point-to-point (N2N) device discovery issue.

  - ERXXXXXX - To wait for ABTS response on I/O timeouts for NVMe.
  Change - qla2xxx: To wait for ABTS response on I/O timeouts for NVMe.

  - ER147523 - BSG stack trace and SCM display issues.
  Change - SCM: Functional regression with a6 release.

  - ER 147413 - edif: Fix issue with DIF enable target discovery.
  Change - qla2xxx: edif: Fix issue with DIF enable target discovery.

  - ER147480 clear ASYNC_ACTIVE flag to allow relogin.
  Change - qla2xxx: fix stuck session.

  - ERXXXXXX - lockdown: add mpi flash lock down support
  Change - qla2xxx: lockdown: add mpi flash lock down support

  - 10.02.00.02.a7-k1 BH 08/22/2020
  - ER147495 - edif changes 
  Change - qla2xxx: edif: fix nvme discovery failure
  qla2xxx: edif: fix els corruption.

  - ERXXXXXX - add mpi flash lock down support
  Change - qla2xxx: lockdown: add mpi flash lock down support

  - ERXXXXXX: SCMR changes
  Change - qla2xxx: SCMR: Correct scmr_outstanding_reqs accounting.
  qla2xxx: SCM: Changes to segregate current_events and current_state.
  qla2xxx: SCMR: Increase local array size.

  - ER147298 : USCM "Congestion Warning" counter regression
  Change - qla2xxx: Correct FPIN Structure Definition (Severity).

  - 10.02.00.02.a6-k1 BH 08/13/2020
  - ERXXXXXX - fix crash on session cleanup + unload.
  Change - qla2xxx: fix crash on session cleanup + unload.

  - ER147329 - edif changes 
  Change - qla2xxx: edif: fix compile error. do not submit
  qla2xxx: edif: fix double free on ELS send failure.
  qla2xxx: edif: reject els if non secure device.
  qla2xxx: edif: reject ELS on session down.
  qla2xxx: edif: redefine purex dest addr to be more consistent.
  qla2xxx: edif: tweak debug messages.
  qla2xxx: edif: fix nvme+edif target connect problem.

  - ER147460 - issue with Diag test on QCC CLI 2.4.0 build 10 with 10.2.00.2-a5 driver
  Change - qla2xxx: edif: move bsg auth els into separate routine.
  qla2xxx: edif: Fix error in BSG ELS path that has valid response data.

  - ER147312 - Add support to report MPI FW state.
  Change - qla2xxx: Add support to report MPI FW state.
  qla2xxx: Fix reset of MPI firmware.
  qla2xxx: Fix MPI reset needed message.

  - 10.02.00.02.a5-k1 BH 07/31/2020
  - ER147418: server crash seen when trying to capture the debugfs stat on isolated port.
  Change - qla2xxx: Don't process target debugfs stats if port is isolated.

  - ERXXXXXX : Add SCM stats to scmr_stats node.
  Change - qla2xxx: Add SCM stats to scmr_stats node.

  - ER147419 : Fix crash due to request q pointer extraction failure.
  Change - qla2xxx: Latency measurement patch.

  - ERXXXXXX : edif: remove redundant field in port_id_t
  Change -qla2xxx: edif: remove redundant field in port_id_t

  - ER147331 : extract bbc from PLOGI template payload.
  Change -qla2xxx: Fix buffer-buffer credit extraction error

  - ERXXXXXX : Split qla2x00_configure_local_loop()
  Change scsi: qla2xxx: Split qla2x00_configure_local_loop()

  - ERXXXXXX : SCMR - Add I/O flow control.
  Change - qla2xxx: SCMR - Add I/O flow control.

  - 10.02.00.02.a4-k1 BH 07/23/2020
  - ER147402 - Do not install nvme auto connect script if OS is installing it.
  Change - qla2xxx: auto-connect scripts are install based on nvme-cli package.

  - ERXXXXXX - Fixed return status of nvme fcp request.
  Change - qla2xxx: Set NVME status code for failed NVME FCP request.

  - ERXXXXXX - Multi-que support for TMF.
  Change - qla2xxx: Multi-que support for TMF.

  - ERXXXXXX ? edif changes
  Change - qla2xxx: edif: simplify reserve/release of sa_index.
  qla2xxx: edif: tweak debug log.
  qla2xxx: edif: adjust ELS resp length.
  qla2xxx: edif: send logo on app stop.
  qla2xxx: edif: remove prlo in session deletion.
  qla2xxx: edif: Fix app stop stall.

  - ER147298 - USCM "Congestion Warning" counter regression w/.65 driver.
  Change - qla2xxx: Correct fpin_descriptor definition.
  qla2xxx: Consolidate EDIF & SCM Purex Calls.

  - ERXXXXXX - Calculate avg. time taken by different components for IO completion.
  Change - qla2xxx: Latency measurement patch.

  - 10.02.00.02.a3-k1 BH 07/16/2020
  - ER147348 - Observing the firmware dump while running the qaucli -g post port isolation.
  Change - qla2xxx: Don't check firmware state in case of chip is down.

  - ER147338 - SLES: Driver load failed - modprobe: ERROR: module 'qla2xxx' is unsupported
  Change - qla2xxx: Add support for loading external modules on SuSE.

  - ER147361 - System panic after enabling port isolated during TimeOutReset.
  Change - qla2xxx: Synchronize the update the host counters using lock.

  - ER147370 - Hardware Error counter not incrementing for MBX command timeout 
  Change - qla2xxx: Update hardware error count for various error conditions.

  - ERXXXXXX - The change is to help in debuggging.
  Change - qla2xxx: Move some messages from debug to normal log level.

  - ER147346 - Observed a call trace after port isolation. 
  Change - qla2xxx: Fix the call trace for flush workqueue.

  - ERXXXXXX - For debug purpose
  Change - qla2xxx: Add error counters to debugfs node

  - 10.02.00.02.a2-k1 AE 07/10/2020
  - ERXXXXXX - qla2xxx: Fix TCM compilation issues.
  Change - Enabled build of tcm_qla2xxx module and fixed compile issues.

  - ERXXXXXX - qla2xxx: edif : Added back the app_stop wait and avoid if link is down.
  Change - Added wait during app stop.

  - ERXXXXXX - qla2xxx: Set BIT_13 for NVMe Async events.
  Change - Driver changes to skip SLER for Async event command.

  - ER147323 - qla2xxx: Correct the check for sscanf return value.
  Change - Driver updated to check version correctly.

  - ERXXXXXX - qla2xxx: v2: Add EDIF support.
  Change - Refactoring EDIF code for modularity.

  - ER147298 - Congestion Warning/Alarm counters fail to increment
  Change - Update driver to increment the counters for congestion signals.

  - 10.02.00.02.a1-k1 AE 06/29/2020
  - qla2xxx: Enable IOCB throttling by default.
  - qla2xxx: Implementation to get and manage host, target stats and initiator port.
  - qla2xxx: Add SLER and PI control support.
  - qla2xxx: Do not log message when reading port speed via sysfs
  - qla2xxx: fix null pointer access.
  - qla2xxx: Use MPI hang trigger to do PEGTUNE halt.
  - qla2xxx: Reduce erroneous error in link reset path
  - qla2xxx: v2: fix stalled N2N reconnect.
  - qla2xxx: Fix warnings on SLES12SP5.
  - qla2xxx: Fix compilation issues on SLES15
  - qla2xxx: Compilation Fixes for SLES15SP1.
  - qla2xxx: Debugfs compilation issue fix for RH7.6.
  - qla2xxx: Fix gcc test compile error output being printed.
  - qla2xxx: Timestamp device online and offline transitions.
  - qla2xxx: Add rport fields in debugfs.
  - qla2xxx: Allow dev_loss_tmo setting for FC-NVMe devices.
  - qla2xxx: Setup debugfs entries for remote ports.
  - qla2xxx: Fix edif related compilation issue on RH7.6.
  - Fixes for compilation on hpe branch
  - qla2xxx: Compilation fixes for RH8.2
  - qla2xxx: Compilation changes for RH7.6
  - qla2xxx: Fixes for compilation on RH7.x I
  - qla2xxx: bsg_job to bsg_job_t
  - qla2xxx: I Unify source code to work with newer kernels.
  - qla2xxx: Makefile changes from code-uni-devel-10x.
  - qla2xxx: qla_edif file changes to compile the driver.
  - qla2xxx: Fix compilation issues.
  - qla2xxx: Fix Makefile issue.
  - qla2xxx: fix compile error
  - qla2xxx: Use explicit LOGO in target mode
  - qla2xxx: Add EDIF support.
  - qla2xxx: Addd edif related files.
  - qla2xxx: Fix MPI failure AEN (8200) handling.
  - qla2xxx: SCM - Backport optimizations and style changes from upstream work.
  - qla2xxx: Fix warning in qla_attr.c file.
  - qla2xxx: Fix nvme compilation error.
  - qla2xxx: Fix crash in alloc w/GFP_KERNEL + interrupt
  - Author : Quinn Tran <qutran@marvell.com> qla2xxx: v2: add iocb resource tracking.
  - qla2xxx: Fix WARN_ON in qla_nvme_register_hba.
  - qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime.
  - qla2xxx: Make tgt_port_database available in initiator mode.
  - qla2xxx: reduce noisy debug message.
  - qla2xxx: Fix mailbox Ch erroneous error
  - qla2xxx: fix login timeout.
  - qla2xxx: Accomodate for SCM FW attribute bit change.
  - qla2xxx: post FC event (FPIN) to transport FPIN handler.
  - qla2xxx: Hide fc_host_fpin_rcv kernel dependency.
  - qla2xxx: Add changes to compile across various kernels.
  - qla2xxx: Use active targets to update SCM stats.
  - qla2xxx: Move SCM functions to qla_isr to keep changes local.
  - qla2xxx: Code to process FLOGI ACC extended payload.
  - qedf: Fix compilation issue - revisit.
  - qla2xxx: SCM Phase 1 Implementation + 2 other patches.
  - qla2xxx: Enable PUREX passthru post ISP reset.
  - qla2xxx: Fix hang when issuing nvme disconnect-all in NPIV.
  - qla2xxx: performance tweak
  - scsi: qla2xxx: fix fcport null pointer access.
  - fixup! qla2xxx: Fix unbound NVME response length.
  - scsi: qla2xxx: Fix unbound NVME response length
  - qla2xxx: Add host attribute to trigger MPI hang.
  - qla2xxx: ONEOFF: silent dbg messages for good path io.
  - qla2xxx: ONEOFF: fix pDIF detection
  - qla2xxx: Snoop inquiry response atleast 168 bytes to determine proprietary DIF.
  - qla2xxx: ONEOFF: add debug counters for T10-PI/DIF
  - qla2xxx: ONEOFF: add MQ support for HP3PAR propritary T10-PI
  - qla2xxx: HPE 3PAR private T10-PI support.
  - qla2xxx: Check for fabric_priority flag during login
  - qla2xxx: use iocb_fabric_priority flag
  - qla2xxx: Fix QoS name and add debug logs
  - qla2xxx: Correction to tests for iocb fabric and fcport qos.
  - qla2xxx: Use ->isp_ops->read_optrom() in qla26xx_read_qos_fcport_table().
  - qla2xxx: QoS fcport table index initialization improvement.
  - qla2xxx: Add QoS fcport table index to speed up search.
  - qla2xxx: Reduce stack on qos fcport priority routines.
  - qla2xxx: HPE: Register FDMI QOS
  - qla2xxx: Add bsg interface for qos lun level bitmask.
  - qla2xxx: Read E2E QoS fcport priority bitmasks from flash.
  - qla2xxx: Abstract qos lun level mask for iocb cs_ctl field.
  - qla2xxx: Add fabric priority qos lun iocb mechanism.
  - qla2xxx: Implement CT command GFO (Get Fabric Object).
  - qla2xxx: Add support for fabric priority per target.
  - qla2xxx: fix mtcp dump collection failure.
  - qla2xxx: Set Nport ID for N2N
  - qla2xxx: Fix crash during device discovery.
  - qla2xxx: Handle NVME status iocb correctly.
  - qla2xxx: Remove restriction of FC T10-PI and NVME
  - qla2xxx: serialize fc_port alloc in N2N
  - qla2xxx: NPIV does not come up after FW dump.
  - qla2xxx: fix RDP respond data format bug.
  - qla2xxx: force semaphore on flash validation failure.
  - qla2xxx: add more FW debug information
  - qla2xxx: Revert: Disable T10-DIF feature with FC-NVMe during probe
  - qla2xxx: Update BPM enablement semantics.
  - qla2xxx: fix FW resource print error.
  - qla2xxx: Use a dedicated interrupt handler for 'handshake-required' ISPs.
  - qla2xxx: Ensure flash updates return possible failure status through bsg interface.
  - qla2xxx: Improved secure flash support messages
  - qla2xxx: fix flag passing error
  - qla2xxx: Use FC generic update firmware options routine for ISP27xx.
  - qla2xxx: Avoid setting firmware options twice in 24xx_update_fw_options.
  - qla2xxX: Add 16.0GT for PCI String
  - qla2xxx: Use FW_STARTED macro
  - qla2xxx: Add fixes for mailbox command
  - qla2xxx: Fix login IOCB flag
  - qla2xxx: Save rscn_gen for new fcport
  - qla2xxx: firmware option 3 is clobbered by speed set
  - qla2xxx: ISP28xx active FW region
  - qla2xxx: Add portname to print logs in qla24xx_logio_entry().
  - qla2xxx: Correction to MB in-direction selection in qla2x00_echo_test().
  - qla2xxx: Correction to selection of loopback/echo test.
  - qla2xxx: Use endian macros to assign static fields in fwdump header.
  - qla2xxx: Add Speed in SFP print information
  - qla2xxx: Fix RDP response size
  - qla2xxx: Handle cases for limiting RDP response payload length.
  - qla2xxx: Add deferred queue for processing ABTS and RDP.
  - qla2xxx: Cleanup ELS/PUREX iocb fields.
  - qla2xxx: Add devid's and conditionals for 28xx.
  - qla2xxx: Add vendor extended FDMI additions and amendments.
  - qla2xxx: Provide separate RDP enable.
  - qla2xxx: Add vendor extended RDP additions and amendments.
  - qla2xxx: Add changes in preparation for vendor extended FDMI/RDP.
  - qla2xxx: Add 2061 PCI ID
  - qla2xxx: Remove all DIX-0 references
  - qla2xxx: Add endianizer macro calls to fc host stats.
  - qla2xxx: Add sysfs node for D-Port Diagnostics AEN data.
  - qla2xxx: Move free of fcport out of interrupt context.
  - qla2xxx: Add beacon LED config sysfs interface.
  - qla2xxx: Add sysfs hooks for FC-NVMe autoconnect

  - 10.01.00.22-k AE 06/29/2020
  - Upstream driver as part of Linux 5.6


author: Prashant Sreedharan <prashant.sreedharan@broadcom.com> 3.137h
changelog:
  - tg3_disable_ints using uninitialized mailbox value to disable interrupts (Severity:Minor)
  - Enhancement for recoverable/unrecoverable errors (Severity:Minor)
  - Add support for RHEL 6.6 (Severity:Minor)
  - Readme file does not indicate tg3.spec location (Severity:Minor)


author: Siva Reddy Kallam <siva.kallam@broadcom.com> 3.137j
changelog:
  - Add support for SLES11SP4 (Severity:Minor)
  - Add support for Debian 7.7 (Severity:Minor)
  - Fixed delay in getting OperationalStatus of the nic on system reboot (Severity:Minor)


author: Sanjeev Bansal <sanjeevb.bansal@broadcom.com> 3.137k
changelog:
  - Add support for linux 3.16.0 kernel (Severity:Minor)
  - Add support for RHEL 4.8 (Severity:Minor)
  - KVM PCI passthrough failed for tg3 on SUSE 11.3 (Severity:Minor)
  - Add support for RHEL 5.11 (Severity:Minor)
  - (SLES11SP4) After installation of tg3 driver, interface(s) don't come up (Severity:Minor)


author: Sanjeev Bansal <sanjeevb.bansal@broadcom.com> 3.137o
changelog:
  - Add work around HW/FW limitations with vlan encapsulated frames (Severity:Minor)
  - Fix for transmit queue 0 timed out when too many gso_segs (Severity:Medium)


author: Siva Reddy Kallam <siva.kallam@broadcom.com> 3.137v
changelog:
  - Backport upstream patches  (Severity:Medium)
  - Add PHY reset workaround in change MTU path for 5717/19/20  (Severity:Medium)
  - Update the copyright (Severity:Minor)


author: Siva Reddy Kallam <siva.kallam@broadcom.com> 3.137w
changelog:
  - Add SLES 15 support  (Severity:Medium)
  - Add RHEL 7.5 support (Severity:Medium)
  - Fix RHEL 6.4 compilation (Severity:Medium)


author: Siva Reddy Kallam <siva.kallam@broadcom.com> 3.137x
changelog:
  - Add Ubuntu 18.04 support  (Severity:Minor)
  - Fix race between tg3_get_stats64() and tg3_free_consistent() (Severity:Minor)
  - Avoid usleep_range() with holding spin lock (Severity:Minor)


